Quick Pack Company is a kraft paper packing tape manufacturer supplying finished water-activated rolls, no-water pressure-sensitive grades, and jumbo stock for converting. The range supports manual benches, activated dispensers, case sealers, and slitting or rewinding lines. Selection should consider carton surface, flap stress, equipment, reinforcement needs, and whether the material will be used directly or converted.
Showing all 3 results
Kraft paper packaging tape follows three purchasing routes. Water-activated grades require controlled moistening. Pressure-sensitive grades apply directly and may use hot-melt rubber, natural rubber, or acrylic systems. Jumbo rolls are supplied for slitting, rewinding, printing, or private-label production.
Review the carton before approving a grade. Recycled board may contain loose fibers or dust, printed and coated surfaces may reduce contact, and overfilled boxes can keep pressure on the flaps. Approval on clean corrugate does not confirm performance on these harder surfaces.
Product Series Main Role Structure Options Typical Use
Finished water-activated rolls Direct sealing after moistening Standard or reinforced Packing benches with compatible dispensers
No-water pressure-sensitive rolls Immediate sealing Standard or reinforced Manual stations and case sealers
Jumbo rolls for converting Slitting, rewinding, or printing Defined by the finished tape Converters and private-label programs
Finished rolls are planned against carton consumption and equipment. Jumbo stock is planned against usable width, converting yield, and the required finished-roll mix. Reinforcement is a structure choice within the relevant route, not a separate supply form.
Start with the hardest production carton and the intended application system. Dust, uneven porosity, coatings, and stiff flaps can change sealing behavior.
Technical figures should state the substrate, conditioning, dwell time, peel angle, peel rate, temperature, and humidity. Standard-panel data supports lot comparison, but it does not replace fiberboard checks or a production-carton trial.
Factor Water-Activated Rolls Pressure-Sensitive Rolls Jumbo Rolls
Equipment Activated dispenser Cutter or case sealer Slitter, rewinder, or printer
Carton check Wetting and fiber contact Contact on difficult board Validate the converted roll
Structure Standard or reinforced Standard or reinforced Confirm before production
Evidence Activation and seal condition Fiberboard adhesion, shear, unwind, edge lifting Slitting, rewinding, and sample comparison
Common error No activation equipment One grade assumed for every carton Parent roll ordered for direct use
Purchase basis Carton volume and dispenser route Shift use, line speed, roll changes Yield, slit plan, finished-roll mix
Machine projects should specify width, core, outer diameter, winding, feed direction, and unwind behavior. Repeat programs should retain the approved carton, equipment route, roll configuration, artwork revision, and reference sample.
Water-activated rolls need equipment that feeds, moistens, and cuts consistently. During a trial, check whether the full width is wetted evenly and whether dry edges remain.
Pressure-sensitive rolls need no water, but width, core, outer diameter, unwind force, and feed direction must match the tool or case sealer. For jumbo rolls, provide slit widths, rewinding lengths, core requirements, winding direction, expected yield, and the finished-roll mix.
Item Typical Range / Customizable Value Product forms Finished rolls / machine rolls / jumbo parent rolls Adhesive activation Water-activated / pressure-sensitive
Adhesive families Starch-based / hot-melt rubber / natural rubber / acrylic
Paper backing Natural kraft / white kraft / writable or printable grades
Construction Non-reinforced / fiber-reinforced
Supply purpose Direct sealing / slitting / rewinding / printed conversion
Carton conditions Standard / recycled / rough / dusty / printed or coated, subject to trial
Application Hand use / dispenser-assisted / compatible case sealer
Equipment data Width / core / outer diameter / winding / feed direction
Converting data Parent-roll width / slit plan / rewinding format / expected yield
Printing Plain / logo / instructions / warning text / repeated artwork
Test references 180-degree peel / fiberboard adhesion / shear / unwind / tensile / elongation
Test conditions Substrate / conditioning / dwell time / peel angle / peel rate / temperature / humidity
Validation Production cartons, including the hardest surface or flap stress
Inspection Unwind / activation / contact / edge lifting / flap reopening / fiber tear
Repeat supply Approved sample / batch ID / lot comparison
Revalidation After carton, coating, equipment, closure, or route changes
Documentation TDS / available test record / material declaration
MOQ basis Plain / printed / reinforced / jumbo quoted separately
Environmental statement Confirm by construction, documents, and destination requirements
Final values depend on the grade, production carton, test method, equipment, and working conditions.
Quick Pack Company configures each program around its application route. Equipment projects should specify core, outer diameter, winding, feed direction, and roll format. Printed programs should confirm artwork, repeat layout, print direction, contrast, and proof approval. Converting projects should provide the parent-roll configuration, slit plan, rewinding format, and finished-roll mix.
For a comparable quotation, provide the production carton or a box sample, identify the dispenser, case sealer, or converting line, and state the adhesive route, printing requirements, estimated consumption, and direct-use or converting purpose. Recurring orders should retain an approved sample, artwork revision, roll configuration, and lot ID.
Use production cartons and include the hardest condition, such as dusty recycled corrugate, printed board, coated cartons, overfilled boxes, or strong flap return.
Apply the tape with the intended dispenser or case sealer. Check immediate contact, edge lifting, flap reopening, fiber tear, and seal condition after representative handling or storage. Where practical, compare clean and dusty cartons from the same board lot. Repeat the trial after relevant board, coating, carton, equipment, or distribution changes.
Confirm direct sealing or converting, activation route, carton condition, equipment, core, winding, printing, consumption, and planned finished-roll mix. Jumbo enquiries should also state converting width, slit plan, and expected yield.
Available files may include a TDS, material declaration, artwork proof, approved sample, and applicable adhesion, shear, unwind, tensile, or elongation records. Reported values should identify the method, substrate, conditioning, and unit.
Keep rolls in original packaging in a clean, dry area away from excess moisture, heat, and rapid temperature changes. After extended storage, recheck paper condition, unwind, activation or initial adhesion, edge lifting, and sealing performance.
MOQ depends on product form, reinforcement, print colors, artwork repeat, proofing, labels, and finished-roll or jumbo supply. Final artwork, roll configuration, slit plan, and a realistic forecast support planning.
